| | | 20,000+ Fresh Resumes Monthly | |
|
|
| |
Click here or scroll down to respond to this candidate53SBEStreet Address 71,Street Address ,000 Power SeriesSpotlightCandidate's Name
Catalog No.VEC156BDThank you for choosing Black & Decker!PLEASE READ BEFORE RETURNING THISPRODUCT FOR ANY REASONSAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. INSTRUCTION MANUAL1TABLE OF CONTENTSIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Charging/Recharging the Spotlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Spotlight Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Battery Replacement/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 12 Volt DC Plug Fuse Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INTRODUCTIONThank Spotlight. you Please for choosing read this the guide Black carefully & Decker before 1,000,use 000 to Power ensure Series optimum performance and to avoid damage to the unit.FEATURES Powerful, focused quartz halogen beam 3-position electronic spotlight dimmer control to conserve power and extend runtimes Protective rubber safety guard (bezel) around lens Rubber safety cap protects battery compartment Comfortable pistol grip and lanyard Battery Status LED Indicator displays battery charge level while charging, or whenever area light is turned on UL listed, built-in 120 volt AC charger 12 volt DC charging adapter included Rechargeable, non-spillable, sealed lead acid battery TRIGGER(ON/OFF AND DIMMERCONTROL)RUBBER BEZELCARRYLANYARDDC CHARGINGPORT120 VOLT ACCHARGER(BACK OF UNIT)BATTERY STATUSLED INDICATORTRIGGER LOCKPISTOL GRIP HANDLEQUARTZ HALOGENBULBIMPORTANT SAFETY INFORMATIONWARNINGS Contains non-spillable sealed lead acid batteries. They must be recycled or disposed of properly. DO NOT dispose of batteries in fire, as this may result in an explosion. DO NOT open battery or short circuit, this may cause the battery to leak or get hot causing personal injury.RISK OF FIRE/ELECTRIC SHOCK do not plug in a power supply without the bulb lens and cover in place. ALL HALOGEN LIGHTS GIVE OFF HEAT. Do not touch lens while operating. Keep combustibles away from spotlight lens. Extreme heat can cause fires. Never place the light face-down on any surface when lit. CAUTIONS Never look directly into the light or shine the light into another persons eyes. Keep sharp objects away from lens it is glass and can break. Do not immerse spotlight in water. Do not drop or throw spotlight. It contains glass and a sealed lead acid battery. Only replace bulb with type indicated in specifications (6 volt, H3 55 watt quartz halogen). Use only with AC or DC charging adapters that are provided with unit. Plug in the charging adapter at the spotlight first, then plug into the charging source. DO NOT OVERCHARGE: AC recharge up to 14 hours maximum. DC recharge up to 14 hours maximum. NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORTSIMULTANEOUSLY. After charging/recharging, disconnect charging adapter or extension cord and wait 5 minutes before use. Do not crush, cut, pull or expose charging adapter cords to extreme heat. Position charging adapter cords so they do not become entangled or become a safety hazard. Keep charging adapter cords away from sharp edges. Use in a dry location only. Do not open body casing. There are no user-serviceable parts inside. THIS UNIT IS NOT ATOY AND SHOULD ONLY BE OPERATED BY ADULTS. KEEP AWAY FROM CHILDREN!Read This Users Manual Before Using This Spotlight. SAVE THESE INSTRUCTIONSThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.3OPERATING INSTRUCTIONSTo turn the Spotlight ON, depress the Trigger. Pressing the Trigger repeatedly at one second intervals advances the brightness level from dim to brightest. To lock the Trigger in the ON position, squeeze the trigger switch and move the trigger locking button (located on the side of the handle) to locked position. The spotlight will stay on until the lock is moved to the OFF position and the trigger is released.CARE AND MAINTENANCEAll batteries lose charge with time, especially when they are warm. Recharge the unit every two months when not in frequent use, preferably using the 120 volt AC method.Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth moistened with a mild solution of water and detergent.The quartz halogen bulb is the only user-replaceable part in the Spotlight. Periodically inspect the condition of adapters, connectors and wires. Spotlight Bulb ReplacementTo replace the bulb, you will need a small Phillips screwdriver and a 6 volt H3 55 watt replacement bulb. During installation, avoid touching the glass part of the bulb. Bulb life may be shortened by installing a bulb with dirt or fingerprints on it. The bulb can be wiped clean with a cloth moistened with alcohol. 1. Disconnect the unit from any charging adapters. 2. Push the rubber bezel forward toward the front of the spotlight to reveal two small Phillips screws in the retaining ring.3. Using the screwdriver, remove (counterclockwise) the two screws. Set them aside.4. Lift off the retaining ring, glass lens and rubber O ring and set them aside. 5. Carefully remove the reflector and bulb assembly. RETAINING RING RUBBERO RINGREFLECTORRUBBEREND CAPRUBBER BEZEL COVERTRIGGER LOCKTRIGGERSWITCHQUARTZ HALOGENBULBTRIGGERTRIGGER LOCK2CHARGING/RECHARGING THE SPOTLIGHTThis unit is shipped in a partially charged state. Charge unit BEFORE first use using the 120 Volt AC Charger for 12-14 hours or until the green Battery Status LED lights. Charge after each use until green LED lights. Charging/Recharging Using the 120 Volt AC ChargerPlug a standard North American 120 volt AC extension cord into the 120 Volt AC Charger on the back of the unit.Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).Charge until the Battery Status LED Indicator green LED lights (approximately 12- 14 hours). DO NOT CHARGE FOR LONGER THAN 14 HOURS. Charging/Recharging Using the 12 Volt DC Charging Adapter Plug the barrel tip of the supplied 12 Volt DC Charging Adapter into the 12 Volt DC Charging Port.Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.Make sure the Spotlight is OFF (the Trigger Lock is in the OFF position and the Trigger is not depressed).Charge until the Battery Status LED Indicator green LED lights (approximately 12-14 hours). DO NOT CHARGE FOR LONGER THAN 14 HOURS. Make sure the DC source (jump-starter, battery pack, vehicle accessory outlet, etc.) is 12 volt DC and is able to supply at least one half amp at 12 volt DC for 8 hours. This means a battery pack should be charged with at least 4 amp hours capacity.Note: When using a vehicles 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the accessory outlet.WARNING NEVER ATTEMPT TO USE THE AC CHARGER AND DC CHARGING PORT SIMULTANEOUSLY.12 VOLT DCCHARGING PORT12 VOLT DC CHARGING ADAPTERBUILT-IN 120VAC CHARGERBATTERY STATUSLED INDICATORSHOUSEHOLD EXTENSION CORD(NOT INCLUDED)5WARNINGS Do not dispose of the battery in fire as this may result in an explosion. Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire). Do not expose battery to fire or intense heat as it may explode. 12 Volt DC Charging Adapter Plug Fuse ReplacementThe fuse in the plug end of the 12 Volt DC Charging Adapter protects the adapters charging circuit. If the 120 Volt AC Charger operates, but the DC charging adapter does not, then this fuse may be opened (blown). To replace the fuse:1. Unscrew the end cap of the DC plug (counterclockwise). 2. Remove spring center contact and fuse.3. Check fuse with a continuity checker.4. If blown, locate a replacement 0.5 amp/250 volt fuse. 5. Replace the fuse, spring, contact and end cap.6. Screw end cap clockwise until it is finger tight DO NOT OVER-TIGHTEN. 7. Test for proper operation of the 12 Volt DC Charging Adapter. TROUBLESHOOTINGNo Battery Status Indicator LEDs Light When Charging 1. Check connection to the 120 Volt AC Charger or 12 Volt DC Charging Port. 2. Check connection to AC or DC power source.3. Confirm there is a functioning AC or DC current. Unit Will Not Operate1. The Spotlight will not operate when charging. Be sure all adapters are disconnected before Spotlight use.2. If you suspect the bulb is blown, check the filament. If the filament is coiled and unbroken, the bulb is not blown. If bulb is blown, replace it. 3. The battery may be completely discharged. Charge the unit following the directions on page 2.SPECIFICATIONSSpotlight Bulb: 6 volt, H3 series, 55 wattBattery: Maintenance-free, sealed lead acid,6 volt, 3 amp hourAC Charger: UL Listed Class 2, 12 volt DC (500 mA) DC Plug Fuse: 0.5A/250 V46. Disconnect the bulb wire from the red power wire. 7. Unsnap the hairpin retaining wires from the reflectors flange. 8. Using the screwdriver, loosen the retaining screw to remove the bulb from the reflector (no need to completely remove this screw). 9. Lift out the bulb and detach wire.10. Insert the replacement bulb into the reflectors flange. 11. Put back and secure the hairpin retaining wires. 12. Connect the bulb power wire to the red power wire. 13. Tighten the retaining screw on the flange.14. Place the reflector in position in the body of the spotlight. 15. Replace the rubber O ring in the groove around the perimeter of the reflector.16. Replace glass and retaining ring so the screw holes are aligned. 17. Secure retaining ring with two screws.18. Replace rubber bezel.19. Operate switch to ensure proper operation of spotlight. WARNINGTo reduce the risk of electric shock, replace bulb with 6 volt H3 55 watt only. Battery Replacement/DisposalBattery ReplacementThe RBRC SealThe RBRC (Rechargeable Battery Recycling Corporation) Seal on the lead acid battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent lead acid batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative. RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada tofacilitate the collection of spent lead acid batteries. Help protect our environment and conserve natural resources by returning the lead acid battery to an authorized Black & Decker service center or to your local retailer for recycling. BULBREFLECTORHAIRPIN RETAININGWIRESPHILLIPSHEADSCREWS |
