| | | 20,000+ Fresh Resumes Monthly | |
|
|
| |
Click here or scroll down to respond to this candidateCandidate's Name
Street Address * PHONE NUMBER AVAILABLE * EMAIL AVAILABLEWORK EXPERIENCESTEVENSON WEIR, Atlanta, GeorgiaConcrete, Mar 2018 -April 2020DriverSlump and mixLoading and unloading materialsPerformed various manual tasks associated with construction and maintenanceProperly follow safety protocol and regulations to ensure safety for self and others.CARTER CONSTRUCTION, Atlanta, GeorgiaConcrete Finisher, Jan 2018 Mar 2018Operate tamping machines or manually roll surfaces to compact earth fills, foundation forms, and finished road materials, according to grade specifications.Set up forms and lay out guidelines for curbs, according to written specifications, using string, spray paint, and concrete/water mixes.Place strips of material such as cork, asphalt, or steel into joints, or place rolls of expansion-joint material on machines that automatically insert material.Operate machines that clean or cut expansion joints in concrete or asphalt and that rout out cracks in pavement.Cut or break up pavement and drive guardrail posts, using machines equipped with interchangeable hammers.Install dies, cutters, and extensions to screeds onto machines, using hand tools.Operate oil distributors, loaders, chip spreaders, dump trucks, and snow plows.Drive and operate curbing machines to extrude concrete or asphalt curbing.Inspect, clean, maintain, and repair equipment, using mechanics' hand tools, or report malfunctions to supervisors.Control traffic.HOLDER CONSTRUCTION, Atlanta, GeorgiaFraming Carpenter, Nov 2014 Jun 2016Position and hold timbers, lumber, or paneling in place for fastening or cutting.Erect scaffolding, shoring, or braces.Clean work areas, machines, or equipment, to maintain a clean and safe job site.Fasten timbers or lumber with glue, screws, pegs, or nails and install hardware.Select tools, equipment, or materials from storage and transport items to work site.Hold plumb bobs, sighting rods, or other equipment to aid in establishing reference points and lines.Align, straighten, plumb, or square forms for installation.Cut timbers, lumber and/or paneling to specified dimensions, and drill holes in timbers or lumber.Smooth or sand surfaces to remove ridges, tool marks, glue, or caulking.Perform tie spacing layout and measure, mark, drill or cut.Secure stakes to grids for constructions of footings, nail scabs to footing forms, and vibrate and float concrete.Construct forms and assist in raising them to the required elevation.Cut tile or linoleum to fit and spread adhesives on flooring for installation.Cut and install insulating or sound-absorbing material.Glue and clamp edges or joints of assembled parts.Install handrails under the direction of a carpenter.Cover surfaces with laminated plastic covering material.LOCAL 148 UNION HALL, Atlanta, GeorgiaColumns Builder, Jan 1999 Nov 2014Set the forms that hold concrete to the desired pitch and depth, and align them.Check the forms that hold the concrete to see that they are properly constructed.Spread, level, and smooth concrete, using rake, shovel, hand or power trowel, hand or power screed, and float.Monitor how the wind, heat, or cold affect the curing of the concrete throughout the entire process.Direct the casting of the concrete and supervise laborers who use shovels or special tools to spread it.Produce rough concrete surface, using broom.Mold expansion joints and edges, using edging tools, jointers, and straightedge.Clean chipped area, using wire brush, and feel and observe surface to determine if it is rough or uneven.Signal truck driver to position truck to facilitate pouring concrete, and move chute to direct concrete on forms.Apply hardening and sealing compounds to cure surface of concrete, and waterproof or restore surface.Operate power vibrator to compact concrete.Chip, scrape, and grind high spots, ridges, and rough projections to finish concrete, using pneumatic chisels, power grinders, or hand tools.Cut out damaged areas, drill holes for reinforcing rods, and position reinforcing rods to repair concrete, using power saw and drill.Waterproof or restore concrete surfaces, using appropriate compounds.Wet concrete surface, and rub with stone to smooth surface and obtain specified finish.Wet surface to prepare for bonding, fill holes and cracks with grout or slurry, and smooth, using trowel.Fabricate concrete beams, columns, and panels.Install anchor bolts, steel plates, door sills and other fixtures in freshly poured concrete or pattern or stamp the surface to provide a decorative finish.Build wooden molds, and clamp molds around area to be repaired, using hand tools.Cut metal division strips, and press them into terrazzo base so that top edges form desired design or pattern.Push roller over surface to embed chips in surface.Apply muriatic acid to clean surface, and rinse with water.Mix cement, sand, and water to produce concrete, grout, or slurry, using hoe, trowel, tamper, scraper, or concrete-mixing machine.Spread roofing paper on surface of foundation, and spread concrete onto roofing paper with trowel to form terrazzo base.EDUCATIONALBANY JOB CORPS, Albany, GeorgiaWelding, Jan 1998 - Sep 1999ADDITIONAL SKILLSBoom Lift, Scissor Lift, and Forklift OperatorFamiliar with a variety of machinery to include but not limited to jack hammer, chipper, air compressors and any kind of saw.Familiarize with all hand or power tools needed to get the job done and an easy learner. |
