| | | 20,000+ Fresh Resumes Monthly | |
|
|
| |
Click here or scroll down to respond to this candidateCandidate's Name
Street Address cell PHONE NUMBER AVAILABLE cell PHONE NUMBER AVAILABLE EMAIL AVAILABLESummary of Skills: Over twenty years experience in the Construction/Building Maintenance fields. Specializing in floor care, detail cleaning, and remodeling, renovation and painting, sanitation, landscaping and recycling; Knowledgeable in the use of both hand and power tools as well as safety procedures and practices. Friendly detail oriented individual, with a strong work ethic and excellent customer service skills.Hotel engineer experience at the rivington hotelDaily routine checks of ac components,, wired thermostats for ac, removed compressor out of units, sheetrock plaster holes in walls, changed light bulbs, sockets, light switches, replace door handles on front closet and bathroom doors,, always maintained a positive attitude when dealing with guess and vendors or customers,, performed maintenance and repair work on interior and exterior of the hotel, basic knowledge or electrical and plumbing, over 17 years carpentry work knowledge,, good communication skills with colleagues at work, inspected areas to make sure safety and preventive maintenance is correct or need to be correctedWork Experience:Completed daily, weekly and monthly checklist on building equipment maintenance procedures and maintained records of scheduled maintenance procedures; Cleaned washbasins and other toilet room facilities; Dusted and polished furniture; Hosed entrance area to keep it debris free; as well as trimmed and edged turf areas; raked and swept leaves and clipped weeds; Stripped, waxed, buffed, and sealed floors; Sorted, processed and transported recyclable and non-recyclable refuse; Vacuumed floors, rugs and carpets; Operated sweepers, vacuums, buffers and other custodial equipment as well as tools in performing building maintenance; Responded to inquiries and handled complaints.Cleaned and prepared construction sites to eliminate possible hazards; Loaded, unloaded, and identified building materials, machinery, and tools, distributing them to the appropriate locations, according to project specifications; Controlled traffic passing in, and around work zones; Erected and dismantled scaffolding, shoring, braces, traffic barricades, ramps, and other temporary structures; Transferred tools, parts, equipment, and supplies to and from work stations and other areas; Disassembled defective equipment to facilitate repair and reassembled equipment when repairs are complete; Held and supplied tools, parts, equipment, and supplies for other workers; Adjusted, maintained, and repaired tools, equipment, and machines, and assisted colleagues with similar tasks; Assembled and maintained physical structures, using hand or power tools.Followed established safety rules and regulations and maintained a safe and clean environment; Measured and marked cutting lines on materials, using a ruler, pencil, chalk, and marking gauge; Shaped and cut materials to specified measurements, using hand tools, machines, and power saws; Installed structures and fixtures, such as windows, frames, floorings, trim, and hardware, using carpenters' hand and power tools; Filled cracks, holes, and joints with caulk, putty, plaster, and other fillers, using caulking guns and putty knives. Covered surfaces with drop cloths and masking tape and paper to protect surfaces during painting; Smoothed surfaces, using sandpaper, scrapers, brushes, steel wool, and sanding machines; Read work orders or receive instructions from supervisors or homeowners to determine work requirements; Applied primers or sealers to prepare new surfaces, such as bare wood or metal, for finish coats;Inspected the surface to be covered to determine its condition, and correct any imperfections that might show through carpet or cause carpet to wear unevenly; Roll out, measure, mark, and cut carpeting to size with a carpet knife, following floor sketches and allowing extra carpet for final fitting; Joined edges of carpet and seam edges where necessary, by sewing and by using tape with glue and heated carpet iron; Cut and trimmed carpet to fit along wall edges, openings, and projections, finishing the edges with a wall trimmer.Work History:Think Outsourcing llcHotel engineerNew York ny 6/23 to presentLibros Masonry corpMason laborer/helperNew york, NY 10/15 to 04/17Think Outsourcing llc. Hotel enginNew York NY 06/23 to 12/23Broad Prince Realtor Handyman/Carpenter New York, NY 03/14 to 01/14CEOConstruction New York, NY 01/09 to 09/13Platinum Bar & LoungeFacility Manager Brooklyn, NY 08/05 to 12/08Brownsville Car ServiceMaintenance Worker Brooklyn, NY 01/05 to 07/05Education, Certifications & Trainings:New York State Department of EducationGeneral Equivalency DiplomaHostos Community College 10Hour Construction OSHAAPEX Vocational SchoolCarpenter CertificationAPEX Vocational School Plumbers HelperNew York State Department of Labor Custodial Maintenance Certification |
