| | | 20,000+ Fresh Resumes Monthly | |
|
|
| |
Click here or scroll down to respond to this candidateCandidate's Name
Street Address Red Maple CourtCentral City, IA. Street Address
Ph. PHONE NUMBER AVAILABLEemail: EMAIL AVAILABLELinkedIn = https://LINKEDIN LINK AVAILABLESummary of Experience:An experienced Systems Integration, Test and Design Engineerwith MIL / ARINC requirements familiarity with a CurrentDOD Secret ClearancePresent Skills:Knowledge Of:EquipmentOperating SystemsProgramming LanguagesApplicationsComponentNetwork AnalyzersWindows 95,98,NT 4.0LabView 3.1, 8.1,8.5,11, 2014,2017MS Office SuiteSystemSpectrum AnalyzersWindows 2000,XP,10HP VeeCanvasAnalogAudio AnalyzersSolaris 2.51C/C++FrontPageDigitalOscilloscopesSolaris 6, 8PerlPADsRF CircuitsRF MatrixLinuxHTMLMS VISOHigh Current DCDC MatrixVisual BasicEPD480 3 VACData Acquisition Sys.ATLASClear CaseMicrowaveBoundary ScanAssemblerDoorsAudioHP 3060APEGAIPERFWI MAXCAREER HISTORYEntegee AgencyTitle: Principal Engineer / Consultant January, 2021 May, 2021Assignment:Leonardo DRS Naval Power Systems, Milwaukee WI* Consulted on High Power UUT test system requirements as well as test system development via requirements.* Consulted on High Power UUT Subsystem test system duplication/Equipment selection & design with updating due to obsolescence.* Mentored Associate Team Lead Engineers* Customer Requirements Contact.ArtechInfo Temp AgencyArtechInfo Title: Lead / ManagerWorked in/as Test / Systems / Integrations & Developer Engineering October, 2018 August, 2019Assignment:Lockheed Martin, Grand Prairie TX* Consulted on Patriot missile subsystem test requirements as well as test system development via requirements.* Consulted on Tactical missile subsystem test requirements as well as test system development via requirements.* Mentored Junior Team Lead Engineers* Selected Equipment for Testing of 1553* Consulted on LabView programing design issues with colleague.Revolutions TechnologiesEngineer Product IIAssignment:John Deere, Waterloo IA. October, 2015 September, 2017* Developed high level requirements for a Telemetric System* Consulted on/ designed a super cap. Alternative to a Lithium Battery for test equipment shut down.* Developed / programmed several Diagnostic programs to Test Diagnose Electro Mechanical Systems* Developed test procedures and documentation for the above program.* Developed test cases for testing the above programs for the above Testing Programs.* Consulted on a new testing procedure to overcome a network limitation.Fastek InternationalLabVIEW / Test Engineer November, 2014 March, 2015Cedar Rapids, IA* My job was to become an expert for a Automated Test System that Tests a 3 phase power supply quickly* I was Fasteks lead Engineer on a Client / Fastek team that documented, disassembled, deployed and reassembleda Automated Test System from the clients one state facility to another state facility.The LabVIEW / Teststand based system tested a avionics 3 phase power supply.* Developed ATE procedure / document for calibrated NI modules replacement.Infobahn Temp AgencyWorked as Test Engineer but title was PCB Engineer November, 2012 March, 2013Assignment:Motorola, Schaumburg, IL* Consulted on hardware implementation for mid power RF VSWR Test.* Made additional modifications to stock power supplies to use in Automatic Test Equipment System.* Modified / Trouble Shot LabView 8.5 code.* Consulted on Automatic Test Equipment wiring (RF / DC) isolation.* Conceptualized High power Attenuator solution for Automatic Test Equipment System.* Assisted colleague in analyzing LabView 11.0 application code.ArtechInfo Temp AgencySr Systems / Test Engineer Consultant May, 2012 July, 2012Assignment:Cabium Networks, Schaumburg, IL.* Analyzed then documented multiple complex Microwave test systems via Visio.* Designed rack layout then racked Microwave test systems.* Consulted on open air vs. cabled testing for microwave test system.* Consulted and set temperature parameters for thermal chamber testing Microwave transceivers.* Staged Fiber to Ethernet Network for Microwave RF Chamber.* Set up and established link, on a point to multi point microwave communication system for testing.ArtechInfo Temp AgencySr Systems Engineer Consultant June, 2011 - December, 2011Assignment:Motorola Solutions, Schaumburg, IL.* Consulted on the project of assembling 3 multipurpose Trunk Radio Test Systems.* Consulted on Integration of new configuration application software and an embedded Linux Applications.Ultra Criticom May 02, 2011 Mid June 2011* Due to the sensitivity nature of the information; I can not elaborate on this position due to National Security.Aerotek Temp AgencySr. Systems Engineer April, 2009 April, 2010Assignment:Rockwell Collins Government Systems, Cedar Rapids IA.* Wrote requirements, Architect and was a Project Lead for a Classified RF Testing Lab and Secure Network forassembly and testing of main and sub modules for the Joint Tactical Radio System* Captured requirements for JTRS for the purpose of verification & validation testing.* Consultant for Project Managers on the JTR System.* Mentored Junior Engineers and Technicians.* Published Integrations Procedures, Acceptance Test Plans Requirements and Procedure document for JTRSsub modules.* Consultant on RF and Low Bandwidth Digital Data multiplexing circuit for control communication bus betweenantenna and impedance matching circuit.* Consultant on software embedded power sequencing / controller board sub module.Rockwell Collins, Cedar Rapids IA.Sr. Test Equipment Engineer October, 2006 March, 2009* Integrated JTR System in ground motion detecting sensing transceivers with test station hardware / software.* Wrote requirements, Architected and was Team Lead for a $500,000 ATE Project, Delivered 1 monthahead of a 12-month schedule and on budget. This was for a Windows CE embedded telecom black box,for small to mid-class Jets. I trouble shot the build for network auto hook up in addition BIOS configuration.*Assigned to a tigers team as the Program Test Systems Manager to identify, evaluate and help.This included resolving communications process problems between engineering and the test group,identifying manpower needs in several different areas as well as identifying a lack of vendor delivery dates.In addition to conveying this information to upper level management with the idea of approaching theproblem using the bottom to top model. This allowed the dates to go outside the customers schedule so theproblems could be identified and resolved.* Updated a LabView Pass / Fail test program from 7.21 to 8.5 for a Government Systems embedded SoftwareDefined Radio.* Wrote requirements and Designed a Robotic Endurance Test System to qualify a fly by wire Lateral andElevator control system for a 290-passenger jet with a 8,000 nautical mile range.* Developed and integrated test equipment hardware for a Traffic Avoidance and Navigation System /Secondary Radar.* Provided systems engineering and integration support using EPD / DX Designer.* Re / design Test equipment PC interface boards using EPD / DX Designer.* Guided and instructed co-ops and high school interns employees as well as contractors.* Designed / Developed requirements for ATE Systems and UUT Testing.* Acquired test requirements through continues meetings with box developers.Manpower Temp, Arlington Heights, IL.Electronics Engineer 1 May 8, 2006 - September 1, 2006Electronics Engineer 3 September 2005 - May 6, 2006Assignment:Motorola Corporation Schaumburg IL.* Note: WiMAX and LTE have similar attributes as in OFDMA, as well as others.* Worked on the Astro System Security Server and am familiar with the Canopy Product.* Designed T1/E1 WAN communications system for a Public Safety Trunk-ed radio and Data System.* I was responsible for writing System Integration Test Cases* I was part of a 3-person team that mirror imaged a ~ 32-person team with the following responsibilities:Project Management, Test Architects, Test Development, and all process related documentationin addition to other functions areas for a UMTS /Wi MAX* Put together and was in charge of a $3,000,000 dollar plus budget for our team. This included moneyfor on- and off-site projects for the UMTS / Wi MAX* Plan system integration test strategy involving multi team scheduling of the UMTS/Wi MAX product releases.* Was a major contributor to a team published document that planned the testing strategy, staffing and datesneeded to achieve a dated release using Doors as to retrieve & store requirements as needed.* Involved in multi team documentation reviews.* Technical lead of a RF Systems Integration / System Test Team project. for a UMTS / Wi MAX system.* Wrote requirements, Architect and documented a verification test system using high level product architecturalsystem requirement documents for UMTS / Wi MAX Test System Design specs* Lay out lab plans and set environment requirements for a UMTS / Wi MAX System.* Evaluate & order test equipment and software for a UMTS / Wi MAX System.Total Tech Specialists Temp AgencyTest Engineer July 2004 October 2004Electronics Technician March 2004 - July 2004, July 2003 January 2004, March 2003 May 2003Assignment:Grayhill Corporation LaGrange, IL* Root cause analysis for 7-layer Real Time Operating System microcontroller based product using PADs CADProgram as diagnostic tool.* Pieced together a semi ATE test system for a full SCADA system that included a Microcontroller basedUltrasonic Gas Control System. Communications included RS 232, RS485 and 10 Mb Ethernet using TC/IP.* Verification and Validation of pre-production control systems analog IO board operations, per engineeringspecification.* Component level analyzing of pre-production switching power supply.* Setup and use of thermal test chamber.* Design and setup of manual test equipment / fixture for a double sided reflowed PCB.* Equipment selection and setup.* Setup and running of UL. and SCA. witness testing UL personnel.* Debugging of Visual Basic ATE system hardware.* Consulted on a pre-production microcontroller-based board for thermal issue on the SDRAM bus.* Rewrote C test code for an embedded Linux PC board.* Set up multi-Linux (Unix) boards to compile Kernel using NFS and IP for qualifying purposes.This was to stress the microcontroller and its buses in a environmental chamber +80 to 40 degree C.* Redesigned reset/ voltage watchdog circuit for microcontroller-based Analog to Digital converter boardfor a Gas Controller System using the PADs CAD program.* I was responsible for a FMEA Failure Mode Effect Analysis on a Gas flow meter system that used the CAN Busprotocol for the communications between sub modules.* Setup EMC Testing for an Ultrasonic Gas flow meter system.Motorola Corporation Arlington Heights, IL.Electronics Technician November 1988 - February 2001* Repaired HP 3060A Hardware ICT to board level along with fixtures, Debugged testing software.* Negotiated a deal with Hewlett Packard that saved Motorola $460,000.00 by refurbishing $540,000.00worth of broken equipment to the latest model with full warranty for $40,000.00.* Wrote drivers, calibration routine, UUT pass / fail application & hardware requirements for and Developed andprogrammed an ATE Pass / Fail testing system. Using LabView as the programming language and HP test equipment,for measuring the Pass / Fail UUT Specifications & collect data for pass / fail statistical analysis in a spreadsheetformat to certify pre-production units, for passive as well as Microcontroller based products. These programs wouldinject the correct wave forms into the UUT via the hardware, example DAC I/O Board, Signal Gen., Wave formGen, power supply, voltage or current limited or both. This provides the stimulus for the UUT.* Wrote requirements for, Designed, programmed and developed LabView controlled 3* 21, DC to 5.5 GHz. Analog RF.Switching Matrix in conjunction with HP equipment.* Published user document for S Parameter Automated Test System.* Designed and implemented a 10 MHz standard frequency reference distribution system for a50,000 SF building, the equipment load for this reference was about 1500 pieces.* Accelerated Life Testing set up and data retrieval of a Analog RF. Transceiverscontrolled by a HC11 Microcontroller based control board using / rewriting LabView pass / fail application.* Assisted in running a 10,000 square foot engineering test lab with environmental test chambers.* Assisted in running a 4,000 square foot calibration lab.* Experience using IEE-488, RS232 and Ethernet communications.* Direct vendor contact for ordering and quality issues.* Responsible for training of technical/non-technical personnel.* Analyzed & Repaired Analog, Digital, and Microcontroller based test equipment down to component level.This included but was not limited to the following: Spectrum Analyzers, Power Supplies, DVMs,Monitors, Audio Analyzers, Network Analyzers etc.* Designed ATE, UUT interface Test fixtures. Make cables, Test* Have CDMA experience via being trained on the CDMA base station, In addition to testing its functionality.EDUCATIONAL BACKGROUNDBachelors of Science Electrical Engineering - Trinity College & University, March 22, 2002NAFSA Accredited & Department of Defense (DOD) AcceptedAssociate in Electronics Engineering - Joliet Junior College, May 1992 |
